EVA foam decking built to last for years

The price depends on the deck area. As a guide: design from 499 PLN, EVA foam deck from 799 PLN/m², fitting from 299 PLN/m². You can work out a rough figure yourself — measure the individual deck sections with a tape (length × width), add up the area and multiply by the price per m². We prepare an exact quote after the digital measurement. Important: with us you pay only for the foam actually used — offcuts from the sheets are not charged. Many companies price by the number of sheets consumed, which means you also pay for the waste.

We take on designs and orders from 1 m² upwards. It makes no difference whether you need a deck for a small tender or a yacht over 40 feet — every order gets the same care.

Because we charge for the foam actually used, not for whole sheets. We cut the foam on CNC machines, so we know exactly how much material went into your deck. Offcuts are not charged. Many companies price by the number of sheets consumed — which means you also pay for the scraps that end up in the bin. Not here.

Definitely not. Cheap EVA foam sheets with ready-made simple routing differ from our product in practically every respect. The foam — lower density, less abrasion resistant, fades faster and deforms under UV and heat. The adhesive — a cheap industrial tape that starts letting go after the first season in marine conditions (damp, salt, heat). The routing — simple repeating factory patterns, with no fit to your boat. At NauticDeck we use foam with the right hardness, the complete 3M bonding system with 9775WL adhesive, and we cut every panel on CNC to your boat exactly. It is the difference between a tailored suit and something off a market stall.

Three key differences: 1) We use EVA foam with the right hardness — not too soft (it would wear out), not too hard (comfort underfoot). 2) We work with the complete 3M bonding system: surface preparation chemistry, a dedicated 3M primer and 3M 9775WL adhesive developed specifically for GRP. Most competitors use cheaper substitutes. 3) Precision CNC cutting with a perfect fit to your boat.

We use 3M 9775WL — an adhesive developed for bonding to GRP surfaces, which is exactly what your boat deck is made of. On top of that we work with the complete 3M system: first the chemistry to clean and prepare the surface, then the dedicated 3M primer, and only then the bonding. This three-stage process guarantees a lasting bond even in extreme marine conditions.

Yes. EVA foam has a closed-cell structure, which means it does not absorb water, oil, petrol or any other liquid. Cleaning takes a few minutes — warm water and soap, or our dedicated EVA deck cleaner, is enough to make the deck look new again.

Our foam has a built-in UV filter guaranteed for at least 3,000 hours of sun exposure. That means resistance to fading and degradation through many seasons of heavy use. Unlike synthetic teak, EVA foam does not get excessively hot even in full sun.

No — provided it is fitted correctly. That is why we work with the complete 3M bonding system (surface preparation + primer + 9775WL adhesive). A deck fitted according to our procedure does not lift. We guarantee that. Before it reaches us, the foam passes quality control to the highest ISO standards.

Absolutely not. EVA foam is 100% non-slip both dry and soaking wet. This is one of its main advantages over natural teak, which becomes slippery once wet. Safety for the whole crew is guaranteed.

From approving the design to dispatching the finished deck usually takes about 2 weeks. We prepare an exact quote once the deck has been measured digitally. The whole process — from first contact through measurement, design and production to a finished deck — normally takes 3-4 weeks, plus shipping time to your country.

Yes! We supply the deck with 3M 9775WL adhesive already applied to the underside. Every order comes with detailed fitting instructions — you just need to prepare the surface properly (3M chemistry and primer, which we supply), peel off the protective film and stick the panels down. If you would rather have it fitted professionally, we are happy to do it at our facility in Poland.

Practically any boat. We make decks for motorboats, sailing yachts, tenders, RIBs, jet skis and other craft. Every project is individual — we match the deck exactly to the dimensions and shape of your boat using CNC technology.

Yes. Our decks come with a warranty covering the quality of the foam, the durability of the bond and UV resistance. The details are agreed individually. Working with the highest quality materials (premium foam and the complete 3M system), we are confident in how long our products last.

Most likely not. Even two boats of the same model differ in the details: fitting positions, marks left by a previous deck, small differences in finish. Ready-made mats are produced from a single template and do not account for those differences. The result? Gaps, poor alignment and trimming on site. That is why we design every deck individually — from a digital measurement of that specific boat.